243
FERMENTORS
Dry heating system (Plain bottom type vessel(
Single wall vessel
(Plain bottom)
Vessel
10L
7L
5L
3L
13.4
9.3
7
4
Total volume(Liter)
Borosilicate glass / 316L ss for head plate and all fittings
Material
10.4” Color Touch screen Interface
Control panel
Control unit
Remote control through Ethernet (SCADA)
Communication port
Up to 59,994 program for different kinds of condition
Storage Program
Up to 10 data files
Data storage
USB port
Data storage interface
ABS front panel and iron painted housing
Cabinet material
Footprint: 400 x 500 mm (W x D) ; Height: 740 mm
Dimension
110V or 220V ; 50/60 Hz
Rated voltage
2 – 20 LPM
1 – 10 LPM
Inlet Gas Flow-meter
Aeration
Three adjustable Rushton
‐
type impellers
Impeller
Orifice ring
Sparger
Removable 316L stainless steel baffles
Baffle
Bottom heating plate (Base unit)
Heating
Temperature
Cooling coil (Internal heat exchanger)
Cooling
5°C above coolant up to 90°C
Range
Platinum RTD probe (Pt 100); 0 ~ 90°C
Probe
Programmable 15 steps PID controller
Control mode
Removable Top brushless motor
Drive
Agitation
Two type of agitation motor :
a. 30 – 1200 rpm is for general Fermentor;
b. 5 – 300 rpm is for shear
‐
sensitive cell line (optional)
Speed Range
Programmable 15 steps PID controller
Control mode
2-12 pH / Gel-filled electrode; Autoclavable
Range / Probe
pH
PID
Control mode
0 – 200% / Polarographic DO sensor; Autoclavable
Range / Probe
DO
PID; Cascade function to response to
a. Stepping increasing or decreasing agitation speed
b. Oxygen Enrichment Device (optional)
c. To start substrate feeding program.
Control mode
‐
/+ 2000 mV
Transmitter
ORP
Gel
‐
filled electrode; Autoclavable (optional)
Probe
316L stainless steel protector with insulated Teflon tube; On/Off controller
Probe
Foam
Built-in 4 sets of pumps; One external pump (optional)
Peristaltic
pump
Precise Stepping motor; min. speed is 1 rpm
0 – 65 rpm
Speed range
Programmable 15 steps feeding control;
Pump can be assigned for Acid, Base, Anti foam and Substrate
Control mode
316L Stainless steel condenser
Exhaust
Utility Requirement:
1. Building main supply 110V
‐
60 Hz or 220V
‐
50 Hz with
electrical safety cutoff switch.
2. Autoclave for sterilization.
3. Cooling Circulating Water Bath for cooling purpose.
4. Compressor Air to supply air, which comes with a
reducer to control pressure to around 1 kg/cm
2
.
This air is to be dry, oil
‐
free and filtered.
5. Computer for remove control.
Optional Item:
1. Low Speed Agitation Driver : 5 ~ 300 rpm
2. Oxygen Enrichment Device
3. One external pump
Specification :
‐
Model # : MU
‐
D01
‐
Rpm and increment : 20 ~ 300 rpm ; 1 rpm
‐
Motor Type : Brush
‐
less motor
‐
Number of roller : 1
4. Fluorescent Lamp control
‐
Included 4 sets of T5
Fluorescent Lamp and a external Timer on/off
control (24 hr)
5. ORP probe : Gel
‐
filled electrode; Autoclavable
F
